Cisco UCS 5108上的Series Fabric Extenders-Mnet
Cisco UCS 6100 Series Fabric InterconnectsCisco UCS 2100 Series Fabric Extenders
Cisco Unified Computing System Overview
The Cisco® Unified Computing System is a next-generation data center platform that unites compute, network, storage access, and virtualization into a cohesive system designed to reduce total cost of ownership (TCO) and increase business agility. The system integrates a low-latency, lossless 10 Gigabit Ethernet unified network fabric with enterprise-class, x86-architecture servers. The system is an integrated, scalable, multichassis platform in which all resources participate in a unified management domain (Figure 1). Figure 1. The Cisco Unified Computing System Is a Highly Available Cohesive Architecture
Product Overview
Cisco UCS 2100 Series Fabric Extenders bring the unified fabric into the blade server enclosure, providing 10 Gigabit Ethernet connections between blade servers and the fabric interconnect, simplifying diagnostics, cabling, and management.The Cisco UCS 2100 Series extends the I/O fabric between the Cisco UCS 6100 Series Fabric Interconnects and the Cisco UCS 5100 Series Blade Server Chassis, enabling a lossless and deterministic Fibre Channel over Ethernet (FCoE) fabric to connect all blades and chassis together. Since the fabric extender is similar to a distributed line card, it does not do any switching and is managed as an extension of the fabric interconnects. This approach removes switching from the chassis, reducing overall infrastructure complexity and enabling the Cisco Unified Computing System to scale to many chassis without multiplying the number of switches needed, reducing TCO and allowing all chassis to be managed as a single, highly available management domain.The Cisco 2100 Series also manages the chassis environment (the power supply and fans as well as the blades) in conjunction with the fabric interconnect. Therefore, separate chassis management modules are not required.Cisco UCS 2100 Series Fabric Extenders fit into the back of the Cisco UCS 5100 Series chassis. Each Cisco UCS 5100 Series chassis can support up to two fabric extenders, enabling increased capacity as well as redundancy (Figure 2). Figure 2. Rear of Cisco UCS 5108 Blade Server Chassis with Two Cisco UCS 2104XP Fabric Extenders Inserted
Cisco UCS 2104XP Fabric Extender
The first product in the Cisco UCS 2100 Series is the Cisco UCS 2104XP Fabric Extender (Figure 3). It has four 10 Gigabit Ethernet, FCoE-capable, Small Form-Factor Pluggable Plus (SFP+) ports that connect the blade chassis to the fabric interconnect. Each Cisco UCS 2104XP has eight 10 Gigabit Ethernet ports connected through the midplane to each half-width slot in the chassis. Typically configured in pairs for redundancy, two fabric extenders provide up to 80 Gbps of I/O to the chassis. Figure 3. Cisco UCS 2104XP Fabric Extender
Features and Benefits
Table 1 summarizes the main features and benefits of the Cisco UCS 2100 Series. Table 1. Features and Benefits
Feature
Benefit
Management by Cisco UCS Manager
· Reduces TCO by removing management modules from the chassis, making the chassis stateless· Provides a single, highly available management domain for all system chassis, reducing administrative tasks Autoconfiguration
Simplifies operation by automatically synchronizing firmware levels between the fabric extenders and the interconnects
Unified fabric
· Decreases TCO by reducing the number of network interface cards (NICs), host bus adapters (HBAs), switches, and cables needed· Transparently encapsulates Fibre Channel packets into Ethernet Automatic failover
Increases availability with an active-active data plane
Scalable bandwidth
Reduces TCO by optimizing overall system capacity to match actual workload demands
Environmental monitoring
Removes the need for chassis management modules
Lossless fabric
Provides a> Priority flow control (PFC)
· Simplifies management of multiple traffic flows over a single network link· Supports different> Systemwide bandwidth management
Enables consistent and coherent quality-of-service (QoS) management throughout the system
Cisco VN-Link technology
· Enables a consistent operational model between virtual and physical environments· Provides the same level of network visibility for virtualized and non-virtualized environments· Improves diagnostic and troubleshooting capabilities in a virtual environment· Simplifies network and security policy enforcement when migrating virtual machines from one host to another SFP+ ports
· Increases flexibility with a range of interconnect solutions, including copper Twinax cable for short runs and fiber for long runs.· Consumes less power per port than traditional solutions Product Specifications
Cabling
Table 2 presents cabling specifications for the Cisco UCS 2100 Series. Table 2. Cabling Specifications
Connector (Media)
Cable
Distance
Power (Each Side)
Transceiver Latency (Link)
Standard
SFP+ copper (CU)
Twinax
1, 3, and 5m
~0.1 watt (W)
~0.1 microsecond
SFF 8431
SFP+ short reach
(SR) and multimode fiber (MMF)
MM OM2
MM OM3
82m
300m
1W
~0 microseconds
IEEE 802.3ae
SFP+ long reach (LR) MMF and SR
SMF
Up to 300m over SMF
1W
~0 microseconds
IEEE 802.3ae
Performance
· Hardware forwarding at 160 Gbps
· Low-latency cut-through design provides predictable, consistent traffic latency regardless of packet> Layer 2
· Layer 2 VLAN trunks
· IEEE 802.1Q VLAN encapsulation
· Support for up to 256 VLANs and virtual SANs (VSANs)
· Support for Cisco VN-Link architecture
· Jumbo frames on all ports (up to 9216 bytes)
· Pause frames (IEEE 802.3x)
QoS
· Layer 2 IEEE 802.1p (CoS)
· CoS-based egress queuing
· Egress strict-priority queuing
· Egress port-based scheduling: Weighted Round-Robin (WRR)
· Four hardware queues per port
High Availability
· Up to two fabric extenders can work in the Cisco UCS 5100 Series Blade Server Chassis
· Active-active data plane operation with failover
· Capability to fail over from one fabric extender to the other in the event of a failure
· Active-passive management plane operation
· Support for nonstop management plane functioning; if the active fabric extender fails, the passive fabric extender takes over the chassis management needs
Management
· Management of fabric extenders integrated into Cisco UCS Manager (please refer to the Cisco UCS Manager data sheet for more information about management interfaces)
· Capability to manage blade server chassis components such as power supplies, fans, and blades in conjunction with the fabric interconnect
· Firmware levels between the fabric extender and fabric interconnect always synchronized
Low-Latency, Lossless 10 Gigabit Ethernet Unified Network Fabric
· PFC (per-priority pause frame support)
· Data Center Bridging Exchange (DCBX) Protocol
· IEEE 802.1Qaz: Bandwidth management
Industry Standards
· IEEE 802.1p: CoS prioritization
· IEEE 802.1Q: VLAN tagging
· IEEE 802.3: Ethernet
· IEEE 802.3ad: LACP
· IEEE 802.3ae: 10 Gigabit Ethernet
· SFP+ support
Physical Specifications
SFP+ Optics
Cisco Unified Computing System products support 10 Gigabit Ethernet SFP+ copper Twinax cables for short distances and SFP+ optics for longer distances. SFP+ has several advantages compared to other 10 Gigabit Ethernet connectivity options, including: · Small 10 Gigabit Ethernet form factor
· Optical interoperability with XENPAK, X2, and 10 Gigabit Small Form-Factor Pluggable (XFP) interface types
· Low power consumption
· Hot-swappable device
Environment
· Physical (height x> · Operating temperature: 32 to 104°F (0 to 40°C)
· Nonoperating temperature: -40 to 158°F -40 to 70°C)
· Humidity: 5 to 95% (noncondensing)
·> Weight
· 2.5 lb (1.134 kg)
Regulatory Standards Compliance: Safety and EMC
Table 3 summarizes Cisco UCS 2100 Series regulatory compliance. Table 3. Regulatory Standards Compliance: Safety and EMC
Specification
Description
Regulatory compliance
Products should comply with CE Markings according to directives 2004/108/EC and 2006/95/EC
Safety
· UL 60950-1· CAN/CSA-C22.2 No. 60950-1· EN 60950-1· IEC 60950-1· AS/NZS 60950-1· GB4943 EMC: Emissions
· 47CFR Part 15 (CFR 47)>· AS/NZS CISPR22>· CISPR22>· EN55022>· ICES003>· VCCI>· EN61000-3-2· EN61000-3-3· KN22>· CNS13438> EMC: Immunity
· EN50082-1· EN61000-6-1· EN55024· CISPR24· EN300386· KN 61000-4 series RoHS
The product is RoHS 5-compliant with exceptions for leaded ball grid array (BGA) balls and lead press-fit connectors
This technolgy document copyed from Cisco Officewebsite:
http://www.cisco.com/en/US/prod/collateral/ps10265/ps10278/data_sheet_c78-524729_ps10276_Products_Data_Sheet.html
最近在测试UCS与虚拟化环境，真的是觉得很强大，技术发展的快，希望快点跟上！
页:
[1]