DHCP server configuration on the Cisco Aironet 1100 and 1200 series AP
DHCP server configuration on the Cisco Aironet 1100 and 1200 series AP
https://supportforums.cisco.com/docs/DOC-3628
Resolution
Dynamic Host Configuration Protocol (DHCP) server capability was first available on the Cisco Aironet 1100 and 1200 series Access Points (APs) in version 12.2(11)JA1.
When an AP is configured as a DHCP server, it can provide IP addresses to an Ethernet-capable PC connected to its Ethernet port or to wireless client devices that associate to the AP.
Setting up the DHCP Server
By default, access points are configured to receive IP settings from a DHCP server on your network. You can also configure an access point to act as a DHCP server to assign IP settings to devices on both your wired and wireless LANs.
The access point becomes a mini-DHCP server by default when it is configured with factory default settings and it cannot receive IP settings from a DHCP server. As a mini-DHCP server, the access point provides up to 20 IP addresses between 10.0.0.11 and 10.0.0.30 to a PC connected to its Ethernet port and to wireless client devices configured to use no SSID, and with all security settings disabled. The mini-DHCP server feature is disabled automatically when you assign a static IP address to the access point. Because it has a console port to simplify initial setup.
Note When you configure the access point as a DHCP server, it assigns IP addresses to devices on its subnet. The devices communicate with other devices on the subnet but not beyond it. If data needs to be passed beyond the subnet, you must assign a default router. The IP address of the default router should be on the same subnet as the access point configured as the DHCP server.
For detailed information on DHCP-related commands and options, refer to the Configuring DHCP chapter in the Cisco IOS IP Configuration Guide, Release 12.3. Click this URL to browse to the "Configuring DHCP" chapter:
http://www.cisco.com/univercd/cc/td/doc/product/software/ios122/122cgcr/fipr_c/ipcprt1/1cfdhcp.htm
Beginning in privileged EXEC mode, follow these steps to configure an access point to provide DHCP service and specify a default router:
Command
Purpose Step 1
configure terminal
Enter global configuration mode.
Step 2
ip dhcp excluded-addresslow_address [ high_address ]
Exclude the wireless device IP address from the range of addresses thewireless device assigns. Enter the IP address in four groups ofcharacters, such as 10.91.6.158.
the wireless device assumes that all IP addresses in a DHCP address poolsubnet are available for assigning to DHCP clients. You must specifythe IP addresses that the DHCP Server should not assign to clients.
(Optional) To enter a range of excluded addresses, enter the address atthe low end of the range followed by the address at the high end of therange.
Step 3
ip dhcp poolpool_name
Create a name for the pool of IP addresses that the wireless deviceassigns in response to DHCP requests, and enter DHCP configuration mode.
Step 4
networksubnet_number
Assign the subnet number for the address pool. The wireless device assigns IP addresses within this subnet.
(Optional) Assign a subnet mask for the address pool, or specify thenumber of bits that comprise the address prefix. The prefix is analternative way of assigning the network mask. The prefix length must bepreceded by a forward slash (/).
Step 5
lease { days [ hours ] [ minutes ] |
infinite }
Configure the duration of the lease for IP addresses assigned by the wireless device.
·http://www.cisco.com/en/US/i/templates/blank.gifdays—configure the lease duration in number of days
·http://www.cisco.com/en/US/i/templates/blank.gif(optional) hours—configure the lease duration in number of hours
·http://www.cisco.com/en/US/i/templates/blank.gif(optional) minutes—configure the lease duration in number of minutes
·http://www.cisco.com/en/US/i/templates/blank.gifinfinite—set the lease duration to infinite
Step 6
default-router address
Specify the IP address of the default router for DHCP clients on thesubnet. One IP address is required; however, you can specify up to eightaddresses in one command line.
Step 7
end
Return to privileged EXEC mode.
Step 8
show running-config
Verify your entries.
Step 9
copy running-config startup-config
(Optional) Save your entries in the configuration file.
Use the no form of these commands to return to default settings.
This example shows how to configure the wireless device as a DHCP server, exclude a range of IP address, and assign a default router:
AP# configure terminal
AP(config)# ip dhcp excluded-address 172.16.1.1 172.16.1.20
AP(config)# ip dhcp pool wishbone
AP(dhcp-config)# network 172.16.1.0 255.255.255.0
AP(dhcp-config)# lease 10
AP(dhcp-config)# default-router 172.16.1.1
AP(dhcp-config)# end
To configure DHCP service on the AP, refer to the Configuring DHCP Service section of Administering the Access Point.
Note: When you use an external DHCP server to provide IP addresses and if the DHCP server is behind a router you can use the ip helper-addresscommand to forward the bootp broadcast packets received on the Router interface to the DHCP server. DHCP protocol information is carried inside of BOOTP packets. To enable BOOTP broadcast forwarding for a set of clients, configure a helper address on the router interface closest to the client. The helper address should specify the address of the DHCP server. If you have multiple servers, you can configure one helper address for each server. Because BOOTP packets are forwarded by default, DHCP information can now be forwarded by the router. The DHCP server now receives broadcasts from the DHCP clients. For more information on the usage of this command read ip helper-address command.
ip helper-address;-
To enable the forwarding of User Datagram Protocol (UDP) broadcasts, including BOOTP, received on an interface, use the ip helper-address command in interface configuration mode. To disable the forwarding of broadcast packets to specific addresses, use the no form of this command.
ip helper-address address
no ip helper-address address
Syntax Description
vrf name
(Optional) Enables VPN routing and forwarding (VRF) instance and VRF name.
global
(Optional) Configures a global routing table.
address
Destination broadcast or host address to be used when forwarding UDPbroadcasts. There can be more than one helper address per interface.
redundancyvrg-name
(Optional) Defines the VRG group name.
Examples;-
The following example defines an address that acts as a helper address:
interface ethernet 1
ip helper-address 121.24.43.2
The following example defines an address that acts as a helper address and is associated with the VRF named red:
interface ethernet 1/0
ip helper-address vrf red 121.25.44.2
The following example defines an address that acts as a helper address and is associated with the VRG named shop:
interface ethernet 1/0
ip helper-address 121.25.45.2 redundancy shop
Administering the Access Point:-
http://www.cisco.com/en/US/docs/wireless/access_point/12.4_3g_JA/configuration/guide/s43adm.html
Problem Type
Configure / Configuration issues
Products
Access point
页:
[1]