How To Install Nginx on CentOS 7（转）

vlei

How To Install Nginx on CentOS 7

PostedJuly 22, 2014 427.4kviews NGINX CENTOS


About Nginx
　　Nginx is a high performance web server software. It is a much more flexible and lightweight program than Apache HTTP Server.
　　This tutorial will teach you how to install and start Nginx on your CentOS 7 server.



Prerequisites
　　The steps in this tutorial require the user to have root privileges. You can see how to set that up by following steps 3 and 4 in the Initial Server Setup with CentOS 7 tutorial.



Step One—Add Nginx Repository
　　To add the CentOS 7 EPEL repository, open terminal and use the following command:

sudo yum install epel-release



Step Two—Install Nginx
　　Now that the Nginx repository is installed on your server, install Nginx using the following yum command:

sudo yum install nginx

　　After you answer yes to the prompt, Nginx will finish installing on your virtual private server (VPS).



Step Three—Start Nginx
　　Nginx does not start on its own. To get Nginx running, type:

sudo systemctl start nginx

　　If you are running a firewall, run the following commands to allow HTTP and HTTPS traffic:

sudo firewall-cmd --permanent --zone=public --add-service=http
sudo firewall-cmd --permanent --zone=public --add-service=https
sudo firewall-cmd --reload

　　You can do a spot check right away to verify that everything went as planned by visiting your server's public IP address in your web browser (see the note under the next heading to find out what your public IP address is if you do not have this information already):

http://server_domain_name_or_IP/

　　You will see the default CentOS 7 Nginx web page, which is there for informational and testing purposes. It should look something like this:

　　If you see this page, then your web server is now correctly installed.
　　Before continuing, you will probably want to enable Nginx to start when your system boots. To do so, enter the following command:

sudo systemctl enable nginx

　　Congratulations! Nginx is now installed and running!

How To Find Your Server's Public IP Address
　　To find your server's public IP address, find the network interfaces on your machine by typing:

ip addr

1. lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN
. . .
2: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP qlen 1000
. . .

　　You may see a number of interfaces here depending on the hardware available on your server. The lointerface is the local loopback interface, which is not the one we want. In our example above, the eth0interface is what we want.
　　Once you have the interface name, you can run the following command to reveal your server’s public IP address. Substitute the interface name you found above:

ip addr show eth0 | grep inet | awk '{ print $2; }' | sed 's/\/.*$//'



Server Root and Configuration
　　If you want to start serving your own pages or application through Nginx, you will want to know the locations of the Nginx configuration files and default server root directory.

Default Server Root
　　The default server root directory is /usr/share/nginx/html. Files that are placed in there will be served on your web server. This location is specified in the default server block configuration file that ships with Nginx, which is located at /etc/nginx/conf.d/default.conf.

Server Block Configuration
　　Any additional server blocks, known as Virtual Hosts in Apache, can be added by creating new configuration files in /etc/nginx/conf.d. Files that end with .conf in that directory will be loaded when Nginx is started.

Nginx Global Configuration
　　The main Nginx configuration file is located at /etc/nginx/nginx.conf. This is where you can change settings like the user that runs the Nginx daemon processes, and the number of worker processes that get spawned when Nginx is running, among other things.



See More
　　Once you have Nginx installed on your cloud server, you can go on to install a LEMP Stack.