设为首页 收藏本站
查看: 404|回复: 0

[经验分享] What is the difference between M1 and F1 Cisco Nexus Line cards?

[复制链接]

尚未签到

发表于 2018-7-17 06:28:21 | 显示全部楼层 |阅读模式
  Cisco Nexus series switches brought a new technology to the data   center. The whole designed is changed from the Catalyst 6500 series.   Nexus is no longer dependent on SUP’s backplane, it is more like a   midplane architecture. Let me elaborate a little on this, what that   statement means that currently if there is any limitation of speed, then   it is posed by the Line Card. Then how the Line cards communicate with   each other, they do with Fabric Modules. Read for further details into   basic architecture difference between Catalyst 6500 vs Nexus 7000

  Nexus Line card modules  fall into two major categories. M1, and F1. There is another variation   to the M1 which is M1-XL. Brad Hedlund wrote a good article that can be   referenced for reading,>  M1, M1-XL

  M1 Series  were the introductory line cards that were offered by Cisco for Nexus.   They come with a fabric of 80GB. These cards have 10Gig links making   them>  1- Delivery at 60 Million Packets per second (Mpps) for layer 2,3 IPv4.
  2- Delivery at 30 Mpps IPv6 unicast.
  3- Delivery of Access Control List (ACL) to 64k entries per module. The   entries include address of Layer 2,3,4 and Cisco’s Metadata fields-   security group tags (SGTs)
  4- in 32 Port line card, each 4 ports share 10GB of Fabric. They can run   either 1 port 10GIG disable 2,3, and 4 OR all 4 in shared mode.
  5- Memory 1GB DRAM
  6- Network management: Cisco DCNM 4.0

  7- Mac addresses table>  8- FIB table of 128k entry
  9- Netflow supports 512k Entry in both Ingres and Egress
  10- 16384 bridge domains and 4096 vlan per Virtual Device Context (VDC)
  11- Policers of 16k entry
  M1-XL Series  offers the flexibility or the performance to be internet-facing   deployment with wider transceivers module support. What it basically   offers the possibility of larger FIB. This can be seen from the   following:
  * up to 1M IPv4 routes (depending on prefix distribution)
  * up to 350k IPv6 routes (depending on prefix distribution)
  This was not possible in the M1 Line Cards. M1-XL does provide extra ACL entries support compared to M1, which increased DRAM
  1- Memory 2GB DRAM
  2- Delivery of Access Control List (ACL) to 128k entries per module.
  3- Network management: Cisco DCNM 5.1
  F1

  F1 Series Line   Cards were introduced after the M1. They provide a slight cheaper and   more port density with ONLY layer 2 forwarding. This makes an>  1- 480 Mpps layer two forwarding
  2- Delivery of Access Control List (ACL) to 32k entries per module. The   entries include address of Layer 2,3,4 and Cisoc’s Metadata fields-   security group tags (SGTs)
  3- in 32 Port line card with 230GB of fabric.
  4- Memory 1GB DRAM
  5- Network managment: Cisco DCNM 5.1

  6- Mac addresses table>  The forwarding engine is something new. Every two ports are connected  by  a switch on chip. (SoC), these SoC are the forwarding engine. So  each  SoC supports 16k. What this implies (How marketing figured came)  that  for 32 port, we have 16 SoC. With careful planning, if we use one  VLAN  per SoC we get total of 256k of Mac address support. But if we  span one  vlan among all SoC then we are bounded by max limit of 16k MAC  entry.
  These cards have the Cisco FiberPath Technology. From the data sheet
  The benefits of Cisco FabricPath include:
  · Operational simplicity: Cisco FabricPath embeds an autodiscovery   mechanism that does not require any additional platform configuration.   By offering Layer 2 connectivity, this “VLAN anywhere” characteristic   simplifies provisioning and offers workload flexibility across the   network.
  · High resiliency and performance: Since Cisco FabricPath is a Layer 2   routed protocol, it offers stability, scalability, and optimized   resiliency along with network failure containment.
  · Massively scalable fabric: By building a forwarding model on 16-way   ECMP, Cisco FabricPath helps prevent bandwidth bottlenecks and allows   capacity to be added dynamically, without network disruption.
  They also have the ability to connect FCoE. these features include
  1-Virtual Sans (VSANs)
  2-Inter-VSAN Routing
  3-PortChannels (UP to 16 links)
  4- Storage VDC.
  This sums up what I found. I would include or add more things later as I learn or gather them.

运维网声明 1、欢迎大家加入本站运维交流群:群②:261659950 群⑤:202807635 群⑦870801961 群⑧679858003
2、本站所有主题由该帖子作者发表,该帖子作者与运维网享有帖子相关版权
3、所有作品的著作权均归原作者享有,请您和我们一样尊重他人的著作权等合法权益。如果您对作品感到满意,请购买正版
4、禁止制作、复制、发布和传播具有反动、淫秽、色情、暴力、凶杀等内容的信息,一经发现立即删除。若您因此触犯法律,一切后果自负,我们对此不承担任何责任
5、所有资源均系网友上传或者通过网络收集,我们仅提供一个展示、介绍、观摩学习的平台,我们不对其内容的准确性、可靠性、正当性、安全性、合法性等负责,亦不承担任何法律责任
6、所有作品仅供您个人学习、研究或欣赏,不得用于商业或者其他用途,否则,一切后果均由您自己承担,我们对此不承担任何法律责任
7、如涉及侵犯版权等问题,请您及时通知我们,我们将立即采取措施予以解决
8、联系人Email:admin@iyunv.com 网址:www.yunweiku.com

所有资源均系网友上传或者通过网络收集,我们仅提供一个展示、介绍、观摩学习的平台,我们不对其承担任何法律责任,如涉及侵犯版权等问题,请您及时通知我们,我们将立即处理,联系人Email:kefu@iyunv.com,QQ:1061981298 本贴地址:https://www.yunweiku.com/thread-537828-1-1.html 上篇帖子: cisco交换机开启dhcp服务 下篇帖子: Cisco认证题库、中英文精选资料下载
您需要登录后才可以回帖 登录 | 立即注册

本版积分规则

扫码加入运维网微信交流群X

扫码加入运维网微信交流群

扫描二维码加入运维网微信交流群,最新一手资源尽在官方微信交流群!快快加入我们吧...

扫描微信二维码查看详情

客服E-mail:kefu@iyunv.com 客服QQ:1061981298


QQ群⑦:运维网交流群⑦ QQ群⑧:运维网交流群⑧ k8s群:运维网kubernetes交流群


提醒:禁止发布任何违反国家法律、法规的言论与图片等内容;本站内容均来自个人观点与网络等信息,非本站认同之观点.


本站大部分资源是网友从网上搜集分享而来,其版权均归原作者及其网站所有,我们尊重他人的合法权益,如有内容侵犯您的合法权益,请及时与我们联系进行核实删除!



合作伙伴: 青云cloud

快速回复 返回顶部 返回列表