Cacti监控远程主机时的snmp.conf配置

永不落伍

使用Cacti监控远程主机时的snmp.conf配置实例
使用cacti监控系统时，本机监控一般都比较好弄，可是在监控远程主机时，在snmp的配置这个地方经常容易出画，导致画不出图像来！下面这个是要被cacti监控的主机的snmp.conf的文件配置，需要修改的地方，你的snmp.conf文件中查找以下部分，把你的文件中没有的，添加上，就可以了。下面的IP地址是我随便写的10.10.10.10，这个要改成你的被监控的主机的IP地址。其它的地方照下面的复制粘贴就行了！
有几个地方貌似有点重复，没有太多时间去每个都检验，反正肯定是好用了，呵呵：）暂时就这样喽~~~这东西总是要真正的系统的去使用的时候，才能真正理解其中的每一步的意义。光看理论也没啥意思：）
# vi /etc/snmp/snmpd.conf //被监控的远程主机的
# sec.name source community
com2sec notConfigUser 127.0.0.1 public
com2sec notConfigUser 10.10.10.10 public
# Second, map the security name into a group name:
# groupName securityModel securityName
group notConfigGroup v1 notConfigUser
group notConfigGroup v2c notConfigUser
# Third, create a view for us to let the group have rights to:
# Make at least snmpwalk -v 1 localhost -c public system fast again.
# name incl/excl subtree mask(optional)
view systemview included .1.3.6.1.2.1.1
view systemview included .1.3.6.1.2.1.2
view systemview included .1.3.6.1.2.1.25.1.1
view all included .1
# Finally, grant the group read-only access to the systemview view.
# group context sec.model sec.level prefix read write notif
#access notConfigGroup "" any noauth exact mib2 none none
access notConfigGroup "" any noauth exact all none none
## sec.name source community
#com2sec local localhost COMMUNITY
#com2sec mynetwork NETWORK/24 COMMUNITY
com2sec notConfigUser default public
com2sec *.*.*.0 10.10.10.10/24 public
## group.name sec.model sec.name
group MyRWGroup any local
group MyROGroup any mynetwork
group notConfigUser any zcom
#group MyRWGroup any otherv3user
## incl/excl subtree mask
view all included .1 80
view mib2 included .iso.org.dod.internet.mgmt.mib-2 fc
## context sec.model sec.level prefix read write notif
access MyROGroup "" any noauth 0 all none none
access MyRWGroup "" any noauth 0 all all all
配置完成后，重启snmp服务：
# service snmpd restart
然后在Cacti的主机使用snmpwalk命令测试一下：
# snmpwalk -v 1 10.10.10.10 -c public
显示一大堆下面的信息就是正常了！
…
DISMAN-EVENT-MIB::mteEventNotificationObjects."_snmpd".'_linkDown' = STRING: _linkUpDown
DISMAN-EVENT-MIB::mteEventNotificationObjects."_snmpd".'_linkUp' = STRING: _linkUpDown
DISMAN-EVENT-MIB::mteEventNotificationObjects."_snmpd".'_mteTriggerFailure' = STRING: _triggerFail
DISMAN-EVENT-MIB::mteEventNotificationObjects."_snmpd".'_mteTriggerFalling' = STRING: _triggerFire
DISMAN-EVENT-MIB::mteEventNotificationObjects."_snmpd".'_mteTriggerFired' = STRING: _triggerFire
DISMAN-EVENT-MIB::mteEventNotificationObjects."_snmpd".'_mteTriggerRising' = STRING: _triggerFire
NOTIFICATION-LOG-MIB::nlmConfigGlobalEntryLimit.0 = Gauge32: 1000
NOTIFICATION-LOG-MIB::nlmConfigGlobalAgeOut.0 = Gauge32: 1440 minutes
NOTIFICATION-LOG-MIB::nlmStatsGlobalNotificationsLogged.0 = Counter32: 0 notifications
NOTIFICATION-LOG-MIB::nlmStatsGlobalNotificationsBumped.0 = Counter32: 0 notifications
…
OK,现在去Cacti的控制台里面去添加远程主机，并添加图像设置，就可以看到曲线图了应该！