centreon分布式体系结构(转官网)

chriszg

　　DistributedArchitecture
　　A distributed architecture is based on central monitoring servers andseveral satellite monitors. The central server consolidates all
monitoring data and offers a user interface which also offers the
possibility to monitor and manage the central server and the satellite
monitors. The satellite monitors send their check results to the centralserver. This type of setup permits distribution of checks - for any
type of reason f.e. remote locations, DMZ, etc.

　　In practice, centcore takes care of the data transfers between
the different servers. The central server has to be equipped with a
complete monitoring installation (Nagios, Centreon, NDOutils, MySQL,
etc.), in contrast with the satellite monitors that only have Nagios andNDOutils installed.
Contents
　　[hide]

• 　　1 Setting up key authentication using SSH
  
• 　　2 Plugin duplication
  
• 　　3 Centreon configuration
  
• 　　4 SUDO configuration
  
• 　　5 Finalization
  
• 　　6 Hosts configuration
  
• 　　7 Some remarks/tips/advice
  

Setting up key authentication using SSH
　　On the central server generate a key pair using ssh-keygen. Accept all defaults.
# su - nagios　　
# ssh-keygen
　　
> Enter file in which to save the key (/usr/local/nagios/.ssh/id_rsa):
　　
> Created directory '/usr/local/nagios/.ssh'.
　　
> Enter passphrase (empty for no passphrase):
　　
> Enter same passphrase again:
　　
> Your identification has been saved in /usr/local/nagios/.ssh/id_rsa.
　　Transfer the public key to the satellite monitor for the Nagios daemon owner.
(Replace {IP_ADDRESS} with the IP address of the satellite monitor.)
# ssh-copy-id -i ~/.ssh/id_rsa.pub nagios@{IP_ADDRESS}　　The last command will ask for the password of nagios on the satellitemonitor.
If these steps are succesfully completed, you should be able to log on
to the satellite monitor via SSH without entering a password.
Plugin duplication
　　Copy all plugins from the central server to the satellite monitor:
# scp /usr/local/nagios/libexec/* nagios@{IP_ADDRESS}:/usr/local/nagios/libexec/　　Warnings:

• 　　Installation path of nagios plugins must be the same on ALL nodes, as they share ressources.cfg where $USER1$ macro defines the path!
  
• 　　When copying plugins be carefull about the architecture of
  your main centreon server and the remote poller (32 bits and 64 bits
  kernel). If your plugins were compiled on a 64 bits architecture it willnot run on a 32 bits system.
  

Centreon configuration
　　Connect to the Centreon interface and configure the satellite monitor.
Configuration > Centreon > Pollers > Add　　
(Status: enabled, Localhost: no, IP address, etc.)

　　Next, duplicate the ndomod configuration for the new poller.
Configuration > Centreon > ndomod.cfg.　　
Select action "Duplicate".
　　
(Status: enabled, Requester: the name of the freshly created poller, IP address: the IP address of the central server, Instance name: must be unique)

　　Next, also duplicate the nagios configuration for the new poller.
Configuration > Nagios > nagios.cfg　　
Select action "Duplicate".
　　
(Status: enabled, Server Nagios configured: the name of the freshly created poller)

SUDO configuration
　　In order to allow the central server to manage the Nagios daemon on the satellite monitor, sudo has to be configured.
Edit /etc/sudoers and add the following lines:
nagios   ALL=NOPASSWD: /etc/init.d/nagios restart　　
nagios   ALL=NOPASSWD: /etc/init.d/nagios stop
　　
nagios   ALL=NOPASSWD: /etc/init.d/nagios start
　　
nagios   ALL=NOPASSWD: /etc/init.d/nagios reload
　　
nagios   ALL=NOPASSWD: /usr/sbin/nagiostats
　　
nagios   ALL=NOPASSWD: /usr/sbin/nagios *
　　The use of "visudo" command is preferd to edit /etc/sudoers file.
Finalization
　　Make sure centcore is running on the central server. If it is not running, start it:
# /etc/init.d/centcore startHosts configuration
　　Finally, attach host/services to the new poller and generate the
configuration for all servers, take a beer and watch your setup go.
Some remarks/tips/advice

• 　　Remote pollers only are supported from version Centreon 2 beta 5.
  
• 　　NDOutils do not give a lot information on why things just
  won't work so make sure NDOutils are compiled with mysql support -
  review the config.log carefully. If NDO2DB is working, you should see a
  mysql session for the configured user on the configured database.
  
• 
  　　The procedures to restart,>
  
• 　　After moving a host to another poller, the host and it's
  services will show up twice in Centreon under 'Monitoring'. The tables
  in the centstatus database should be purged after moving a host.