CentOS 6.3下部署LVS(NAT)+keepalived实现高性能高可用负载均衡
本帖最后由 tgidl 于 2014-1-13 09:34 编辑一、简介
VS/NAT原理图：
二、系统环境
实验拓扑：
系统平台：CentOS 6.3
Kernel：2.6.32-279.el6.i686
LVS版本：ipvsadm-1.26
keepalived版本：keepalived-1.2.4
三、安装
0、安装LVS前系统需要安装popt-static，kernel-devel，make，gcc，openssl-devel，lftp，libnl*，popt*
1、在两台Director Server上分别配置LVS+Keepalived
LVS install -------------
# wget http://www.linuxvirtualserver.or ... ipvsadm-1.26.tar.gz
# ln -s /usr/src/kernels/2.6.32-279.el6.i686//usr/src/linux/
# tar zxvf ipvsadm-1.26.tar.gz
# cd ipvsadm-1.26
# make && make install
Keepalived install -------------
# wget http://www.keepalived.org/software/keepalived-1.2.4.tar.gz
# tar zxvf keepalived-1.2.4.tar.gz
# cd keepalived-1.2.4
# ./configure && make && make install
######### 将keepalived做成启动服务，方便管理##########
# cp /usr/local/etc/rc.d/init.d/keepalived /etc/init.d/
# cp /usr/local/etc/sysconfig/keepalived /etc/sysconfig/
# mkdir /etc/keepalived/
# cp /usr/local/etc/keepalived/keepalived.conf /etc/keepalived/
# cp /usr/local/sbin/keepalived /usr/sbin/
# service keepalived start | stop
2、开启路由转发
# vim /etc/sysctl.conf
net.ipv4.ip_forward = 1
# sysctl -p
3、配置Keepalived
# less /etc/keepalived/keepalived.conf
! Configuration File for keepalived
global_defs { router_id LVS_MASTER #BACKUP上修改为LVS_BACKUP}
vrrp_instance VI_1 { state MASTER #BACKUP上修改为BACKUP interface eth0 virtual_router_id 51 priority 100 #BACKUP上修改为80 advert_int 1 authentication { auth_type PASS auth_pass 1111 } virtual_ipaddress { 10.0.0.227 }}
vrrp_instance LAN_GATEWAY { state MASTER #BACKUP上修改为LVS_BACKUP interface eth1 virtual_router_id 52 priority 100 #BACKUP上修改为80 advert_int 1 authentication { auth_type PASS auth_pass 1111 } virtual_ipaddress { 192.168.10.10 }}
virtual_server 10.0.0.227 80 { delay_loop 6 lb_algo rr lb_kind NAT# persistence_timeout 5 protocol TCP
real_server 192.168.10.4 80 { weight 3 TCP_CHECK { connect_timeout 3 nb_get_retry 3 delay_before_retry 3 connect_port 80 } }
real_server 192.168.10.5 80 { weight 3 TCP_CHECK { connect_timeout 3 nb_get_retry 3 delay_before_retry 3 connect_port 80 } }}
BACKUP服务器同上配置，先安装lvs再安装keepalived，然后配置/etc/keepalived/keepalived.conf，只需将批注部分改一下即可。
4、分别在2台Real Server上面设置网关
把网关都设置成：192.168.10.10
5、在2台RealServer中分别配置HTTP
# yum -y install httpd
# cd /var/www/html/
# cat index.html
<h1>WEB1/192.168.10.4</h1>
# /etc/init.d/httpd start
另一台机器配置一样，过程略。
6、分别在CentOS-LVS_MASTER、CentOS-LVS_BACKUP上执行service keepalived start启动keepalived就可实现负载均衡及高可用集群了；
# service keepalived start
四、测试
####高可用性测试####
模拟故障，将CentOS-LVS_MASTER上的keepalived服务停掉，然后观察CentOS-LVS_BACKUP上的日志，信息如下
从日志中可知，主机出现故障后，备机立刻检测到，此时备机变为MASTER角色，并且接管了主机的虚拟IP资源，最后将虚拟IP绑定在etho设备上。
将CentOS-LVS_MASTER 上的keepalived服务开启后，CentOS-LVS_BACKUP的日志状态。
从日志可知，备机在检测到主机重新恢复正常后，释放了虚拟IP资源重新成为BACKUP角色
####故障切换测试####
故障切换是测试当某个节点出现故障后，Keepalived监制模块是否能及时发现然后屏蔽故障节点，同时将服务器转移到正常节点来执行。
将WEB2节点服务停掉，假设这个节点出现故障，然后主、备机日志信息如下
从以上可以看出，Keepalived监控模块检测到192.168.10.5这台主机出现故障后，将WEB2从集群系统中剔除掉了。 此时访问http://10.0.0.227只能看到WEB1了)
重新启动WEB2节点的服务，日志信息如下：
Keepalived监控模块检测到192.168.10.5这台主机恢复正常后，又将此节点加入集群系统中，再次访问就可以访问到WEB2页面了）
想要对你说的不敢说的爱 会不会有人可以明白
页:
[1]