IBM-P6-550 内存故障处理

loin

[url=]一、故障定位[/url]
[url=]1.1.故障信息[/url]

Log摘要 Error/Event Logs Platform Event Log - 5025732D Created at : 10/27/2013 12:17:24 Driver Name : fips340/b1112a_0842.340 Subsystem : Memory DIMM Event Severity : Unrecoverable Error Action Flags : Report to Operating System Service Action Required HMC Call Home Service Processor Call Home Required Action Status : Processed HMC-Acknowledged Primary System Reference Code Reference Code : B123E504 Hex Words 2 - 5 : 030000F0 28A30110 C13920FF C10000FF Hex Words 6 - 9 : 008126C1 00000103 0E630030 00000000 Normal Hardware FRU Priority : Mandatory, replace all with this type as a unit Location Code : U78A0.001.DNWH1H2-P1-C13-C2 Part Number : 77P6500 CCIN : 31A6 Serial Number : MFG Replacement Unit Id : 0x00810404 Priority : Mandatory, replace all with this type as a unit Normal Hardware FRU Priority : Lowest priority replacement Location Code : U78A0.001.DNWH1H2-P1-C13 Part Number : 10N9725 CCIN : 53E1 Serial Number : YL1078002154 MFG Replacement Unit Id : 0x00811161 Priority : Lowest priority replacement Log Hex Dump 00000000 50480030 0100F000 20131027 12172434 PH.0.... ..'..$4 00000010 20131027 12172439 45000106 00000000 ..'..$9E....... 00000020 00000000 00000000 5025732D 5025732D ........P%s-P%s- 00000030 55480018 01008300 23034000 00000000 UH......#.@..... 00000040 0000A902 01015000 505300EC 0101F000 ......P.PS...... 00000050 02010009 000000E4 030000F0 28A30110 ............(... 00000060 C13920FF C10000FF 008126C1 00000103 .9 .......&..... 00000070 0E630030 00000000 42313233 45353034 .c.0....B123E504 00000080 20202020 20202020 20202020 20202020 00000090 20202020 20202020 C0000027 4C2C481C ...'L,H. 000000A0 55373841 302E3030 312E444E 57483148 U78A0.001.DNWH1H 000000B0 322D5031 2D433133 2D433200 49441C1D 2-P1-C13-C2.ID.. 000000C0 37375036 35303000 33314136 00000000 77P6500.31A6.... 000000D0 00000000 00000000 4D521001 00000000 ........MR...... 000000E0 00000048 00810404 4C2C4C1C 55373841 ...H....L,L.U78A 000000F0 302E3030 312E444E 57483148 322D5031 0.001.DNWH1H2-P1 00000100 2D433133 00000000 49441C1D 31304E39 -C13....ID..10N9 00000110 37323500 35334531 594C3130 37383030 725.53E1YL107800 00000120 32313534 4D521001 00000000 0000004C 2154MR.........L 00000130 00811161 55440094 02043100 00007D0A ...aUD....1...}. 00000140 2F6F7074 2F666970 732F6269 6E2F6475 /opt/fips/bin/du 00000150 6D707379 7374656D 00000000 00000000 mpsystem........ 00000160 00000000 00000000 00000000 00000000 ................ 00000170 00000000 00000000 00000000 00000000 ................ 00000180 00000000 00000000 00000000 00000000 ................ 00000190 00000000 66697073 3334302F 62313131 ....fips340/b111 000001A0 32615F30 3834322E 33343000 00000000 2a_0842.340..... 000001B0 00000000 00000001 00000002 00000801 ................ 000001C0 00000001 0000000F 4D54001C 01003100 ........MT....1. 000001D0 38323034 2D453841 30363145 45333400 8204-E8A061EE34. 000001E0 00000000 53570014 0201F000 00000B00 ....SW.......... 000001F0 00030008 00000001 ........

[url=]1.2.故障定位[/url]

系统内存统计信息
Memory Size:	31616 MB

内存位置统计信息
序号	位置	容量	QUAD
1	U78A0.001.DNWH1H2-P1-C13-C2	4096KB	Pairs A
2	U78A0.001.DNWH1H2-P1-C13-C4	4096KB	Pairs B
3	U78A0.001.DNWH1H2-P1-C13-C7	4096KB	Pairs A
4	U78A0.001.DNWH1H2-P1-C13-C9	4096KB	Pairs B
5	U78A0.001.DNWH1H2-P1-C14-C2	4096KB	Pairs C
6	U78A0.001.DNWH1H2-P1-C14-C4	4096KB	Pairs D
7	U78A0.001.DNWH1H2-P1-C14-C7	4096KB	Pairs C
8	U78A0.001.DNWH1H2-P1-C14-C9	4096KB	Pairs D

[url=]U78A0.001.DNWH1H2-P1-C13-C2[/url]槽位内存预告警；
如果更换内存，以Pair(1组2根)的方式进行更换，更换的槽位为P1-Cn-C2 and P1-Cn-C7.


[url=]二、故障处理[/url]

[url=]2.1.先决条件[/url]

注意

确保系统关机，电源断开 操作时，使用防静电护腕 添加或更换硬件组件之前请作好数据备份。如果部件未正确安装，则可能会导致数据丢失。

[url=]2.2.准备项[/url]

准备确认项
类型	准备项	状态
硬件	笔记本一台	已准备就绪
	网线一根	已准备就绪
	一字、十字螺丝刀各一把	已准备就绪
	防静电护腕一个	已准备就绪
	新内存4根	已准备就绪
软件	HMC环境	已准备就绪
其它

[url=]2.3.操作项[/url]

操作项列表
序号	操作项	操作内容	状态
1	确认系统关机	建议客户应用及业务数据备份
2	佩戴防静电护腕	确认已经佩戴防静电护腕，并且防静电护腕连接到机柜上的未涂漆部分
3	断开电源	断开主电源和次电源
4	移除服务检修盖
5	拆除处理器板
6	将取下的处理器板放置在防静电的材质表面
7	拆开移除处理器前盖
8	确认更换内存位置
9	从防静电包装中取出内存
10	安装内存
11	重新安装处理器板
12	确认故障影响消失	确认新更换的硬件无告警
		确认新的硬件在系统中就绪
		用户确认应用及业务数据不受影响
13	收尾	清理现场，结束工作

[url=]三、参考信息[/url]
[url=]
[/url]
[url=][/url]

Processors and memory	Where to install memory modules
Memory plugged in pairs	Plugthe first pair of memory modules into memory module slots P1-Cn-C2 andP1-Cn-C7. Plug the second pair of memory modules into memory module slotsP1-Cn-C4 and P1-Cn-C9. Important: Memory modulesinstalled on the same processor assembly must be identical in size, speed, andfeature code. After the second pair of memory modules, the memory modulesbecome a quad.
One processor card, memory plugged in quads	·Plug the first quad of memory modules into memory module slotsP1-Cn-C2, P1-Cn-C4, P1-Cn-C7, and P1-Cn-C9. ·Plug the second quad of memory modules into memory module slotsP1-Cn-C1, P1-Cn-C3, P1-Cn-C6, and P1-Cn-C8. Important: Memory modulesinstalled on the same processor assembly must be identical in size, speed, andfeature code. After the second pair of memory modules, the memory modulesbecome a quad.
Multiple processor cards, memory plugged in quads	Memoryshould be balanced on each processor card, unless you have an odd number ofmemory modules. ·Plug the first quad of memory modules into memory module slotsP1-Cn-C2, P1-Cn-C4, P1-Cn-C7, and P1-Cn-C9 on each processor card. ·Plug the second quad of memory modules in slots P1-Cn-C1,P1-Cn-C3, P1-Cn-C6, and P1-Cn-C8 on each processor card. Important: Ensure that thememory modules installed on the same processor assembly are identical in size,speed, and feature code. However, memory module feature codes can be differentbetween processor assemblies.

[url=][/url]

ykwll

此地禁止大小便，违者没收工具。

得过且过

勃起不是万能的，但不能勃起却是万万都不能的!

sofh7777

不要在一棵树上吊死，在附近几棵树上多试试死几次~

lihanchuan125

生活***好玩，因为生活老***玩我!

zycchen

避孕的效果：不成功，便成“人”。

zidong

人生自古谁无死，啊个拉屎不用纸!