(转)LVS三种模式配置总结

jane27

　　原文：http://www.6curl.com/lvs-config/
　　近日.做服务器集群,使用的是LVS架构解决方案,为管理方便,总结LVS三种（LVS-DR,LVS-NAT,LVS-TUN）模式的简要配置,省的自己下次需要去网上
LVS是什么我就不介绍的了,参考
http://www.linuxvirtualserver.org/VS-NAT.html
http://www.linuxvirtualserver.org/VS-IPTunneling.html
http://www.linuxvirtualserver.org/VS-DRouting.html
　　
首先是安装ipvsadm管理程序
下载：http://www.linuxvirtualserver.org/software/
注意对应自己的内核版本
ipvsadm-1.24.tar.gz
tar zxvf ipvsadm-1.24.tar.gz
cd ipvsadm-1.24
make
make install
1： LVS-DR 模式(调度器与实际服务器都有一块网卡连在同一物理网段上)
简要的网络结构如下所示

配置LVS server


引用
#！/bin/sh
VIP=192.168.0.210
RIP1=192.168.0.175
RIP2=192.168.0.145
. /etc/rc.d/init.d/functions
case "$1" in
start)
echo "start LVS of DirectorServer"
#Set the Virtual IP Address
/sbin/ifconfig eth0:1 $VIP broadcast $VIP netmask 255.255.255.255 up
/sbin/route add -host $VIP dev eth0:1
#Clear IPVS Table
/sbin/ipvsadm -C
#Set Lvs
/sbin/ipvsadm -A -t $VIP:80 -s rr
/sbin/ipvsadm -a -t $VIP:80 -r $RIP1:80 -g
/sbin/ipvsadm -a -t $VIP:80 -r $RIP2:80 -g
#Run Lvs
/sbin/ipvsadm
;;
stop)
echo "close LVS Directorserver"
/sbin/ipvsadm -C
/sbin/ifconfig eth0:1 down
;;
*)
echo "Usage： $0 {start|stop}"
exit 1
esac　　
配置 RIP server


引用
#!/bin/bash
VIP=192.168.0.210
LOCAL_Name=50bang
BROADCAST=192.168.0.255 #vip's broadcast
. /etc/rc.d/init.d/functions
case "$1" in
start)
echo "reparing for Real Server"
echo "1" >/proc/sys/net/ipv4/conf/lo/arp_ignore
echo "2" >/proc/sys/net/ipv4/conf/lo/arp_announce
echo "1" >/proc/sys/net/ipv4/conf/all/arp_ignore
echo "2" >/proc/sys/net/ipv4/conf/all/arp_announce
ifconfig lo:0 $VIP netmask 255.255.255.255 broadcast $BROADCAST up
/sbin/route add -host $VIP dev lo:0
;;
stop)
ifconfig lo:0 down
echo "0" >/proc/sys/net/ipv4/conf/lo/arp_ignore
echo "0" >/proc/sys/net/ipv4/conf/lo/arp_announce
echo "0" >/proc/sys/net/ipv4/conf/all/arp_ignore
echo "0" >/proc/sys/net/ipv4/conf/all/arp_announce
;;
*)
echo "Usage: lvs {start|stop}"
exit 1
esac　　
2: LVS-TUN 模式
简要的网络架构如下:

配置lvs server


引用

#!/bin/sh
# description: start LVS of Directorserver
VIP=192.168.25.41（注意，lvs server那台机器2个ip，一个是vip,一个是本身ip例如192.168.25.42）
RIP1=192.168.25.44
RIP2=192.168.25.45
#RIPn=192.168.0.n
GW=192.168.25.254
. /etc/rc.d/init.d/functions
case "$1" in
start)
echo " start LVS of DirectorServer"
# set the Virtual IP Address
/sbin/ifconfig tunl0 $VIP broadcast $VIP netmask 255.255.255.0 up
/sbin/route add -host $VIP dev tunl0
#Clear IPVS table
/sbin/ipvsadm -C
#set LVS
/sbin/ipvsadm -A -t $VIP:80 -s rr
/sbin/ipvsadm -a -t $VIP:80 -r $RIP1:80 -i
/sbin/ipvsadm -a -t $VIP:80 -r $RIP2:80 -i
#/sbin/ipvsadm -a -t $VIP:80 -r $RIP3:80 -i
#Run LVS
/sbin/ipvsadm
#end
;;
stop)
echo "close LVS Directorserver"
ifconfig tunl0 down
/sbin/ipvsadm -C
;;
*)
echo "Usage: $0 {start|stop}"
exit 1
esac　　.
配置real server


引用
#!/bin/sh
# ghb in 20060812
# description: Config realserver tunl port and apply arp patch
VIP=192.168.25.43
. /etc/rc.d/init.d/functions
case "$1" in
start)
echo "Tunl port starting"
ifconfig tunl0 $VIP netmask 255.255.255.0 broadcast $VIP up
/sbin/route add -host $VIP dev tunl0
echo "1" >/proc/sys/net/ipv4/conf/tunl0/arp_ignore
echo "2" >/proc/sys/net/ipv4/conf/tunl0/arp_announce
echo "1" >/proc/sys/net/ipv4/conf/all/arp_ignore
echo "2" >/proc/sys/net/ipv4/conf/all/arp_announce
sysctl -p
;;
stop)
echo "Tunl port closing"
ifconfig tunl0 down
echo 1 > /proc/sys/net/ipv4/ip_forward
echo 0 > /proc/sys/net/ipv4/conf/all/arp_announce
;;
*)
echo "Usage: $0 {start|stop}"
exit 1
esac　　
3: LVS-NAT 模式
简要的网络架构如下图:

配置LVS server


引用
#!/bin/sh
# description: start LVS of Nat
VLAN-IP=202.99.59.110
RIP1=10.1.1.2
RIP2=10.1.1.3
#RIPn=10.1.1.n
GW=10.1.1.1
. /etc/rc.d/init.d/functions
case "$1" in
start)
echo " start LVS of NAtServer"
echo "1" >/proc/sys/net/ipv4/ip_forward
echo "0" >/proc/sys/net/ipv4/conf/all/send_redirects
echo "0" >/proc/sys/net/ipv4/conf/default/send_redirects
echo "0" >/proc/sys/net/ipv4/conf/eth0/send_redirects
echo "0" >/proc/sys/net/ipv4/conf/eth1/send_redirects(内网卡上的)
#Clear IPVS table
/sbin/ipvsadm -C
#set LVS
/sbin/ipvsadm -A -t 202.99.59.110:80 -s wlc
/sbin/ipvsadm -a -t 202.99.59.110:80 -r 10.1.1.2:80 -m -w 1
/sbin/ipvsadm -a -t 202.99.59.110:80 -r 10.1.1.3:80 -m -w 1
#Run LVS
/sbin/ipvsadm
#end
;;
stop)
echo "close LVS Nat server"
echo "0" >/proc/sys/net/ipv4/ip_forward
echo "1" >/proc/sys/net/ipv4/conf/all/send_redirects
echo "1" >/proc/sys/net/ipv4/conf/default/send_redirects
echo "1" >/proc/sys/net/ipv4/conf/eth0/send_redirects
echo "1" >/proc/sys/net/ipv4/conf/eth1/send_redirects(内网卡上的)
/sbin/ipvsadm -C
;;
*)
echo "Usage: $0 {start|stop}"
exit 1
esac　　
配置real server
LVS-Nat 模式的后端机器不需要配置.
tips： -g 表示使用DR方式，-m表示NAT方式，-i表示tunneling方式。