HP-UX.应用HP-UX搭建Fonts Server，结合xManager连接，并在终端显示中文

fdf

1st 确认系统支持中文语言环境
执行 locale 查询
# locale -a | grep zh
输出
zh_CN.hp15CN
zh_CN.utf8
zh_HK.big5
zh_HK.utf8
zh_TW.big5
zh_TW.ccdc
zh_TW.eucTW
zh_TW.utf8
上述为系统所支持的中文语言环境

/（root)#swlist -l fileset International

# Initializing...

# Contacting target "myhost"...

#

# Target:  HP5400-1:/

#

# International                                 B.11.11        International

  International.ARABIC                          B.11.11        ARABIC

  International.BULGARIAN                       B.11.11        BULGARIAN

  International.CHINESES                        B.11.11        CHINESES

  International.CHINESET     
            

以上操作应该说明我已安装了中文环境。

然后编辑/etc/dt/config/Xconfig文件，修改Dtlogin*language:zh_CN.hp15CN

再/sbin/init.d/dtlogin.rc reset

Set-up a Font Server

It is necessary to set up a font server to provide fonts to the Reflection X Xserver so that CDE and HP-UX applications will work correctly. To determine whether or not a font server is already running on the HP-UX system, execute the following command:

     $ ps -ef | grep xfs

If a font server were running, you would see the following process in the process list:

    /usr/bin/X11/xfs -config /etc/X11/fs/config -port 7000 -daem

If a font server is already running, continue with the section "Configuring an Existing Font Server"; otherwise, go to the section "Configuring and Starting a New Font Server"

• 　　CONFIGURING AN EXISTING FONT SERVER
  
  
  
  • Append the following font path to the end of the catalogue= line in the font server's config file, /etc/X11/fs/config:
    
  
  

     $ /usr/dt/config/xfonts/C/

NOTE: All font paths are separated by a comma (,).

• Stop and restart the font server:
  
       $ /sbin/init.d/xfs stop; /sbin/init.d/xfs start
  

NOTE: Stopping and restarting the font server while in use by users on Xterminals could potentially reset their Xserver, causing their session to exit.

　　CONFIGURING AND STARTING A NEW FONT SERVER

Append the following font path to the end of the catalogue= line in the font server's config file, /etc/X11/fs/config:

     /usr/dt/config/xfonts/C/ Set the RUN_X_FONT_SERVER environment variable to 1 in the /etc/rc.config.d/xfs file:

     RUN_X_FONT_SERVER=1 Start the font server:

     $ /sbin/init.d/xfs start

• Verify that the font server has been started:
  
       $ ps -ef | grep xfs
  


• RESOLVING "XFontserver error: Cannot open configuration file." ERRORS
  

If the error, "XFontserver error: Cannot open configuration file." results when trying to start the font server, perform one of the following steps to resolve the problem:

Install the latest font server patch.

• Add the following line to the end of the /etc/rc.config.d/xfs file:
  
  CONFIG_FILE_NAME=/etc/X11/fs/config
  

SETUP Xmanager:

1 进入连接属性，点“Configure”:

　　
2 在配置页面，点“Font”――》“Add Font Server”：

Hostname中写刚才设置的Font Server的IP，port写7000。Apply后就可以连接了