CISCO路由器初始配置简介

lomg

　　System Bootstrap, Version 11.1(20)AA2, EARLY DEPLOYMENT>　　Copyright (c) 1999 by cisco Systems, Inc.C3600 processor with 32768 Kbytes of main memory Main memory is configured to 64 bit mode with parity disabled

　　program load complete, entry point: 0x80008000,>　　###################################################################
　　###################################################################
　　###################################################################
　　###################################################################
　　###################################################################
　　###################################################################
　　###################################################################
　　[OK]
　　Restricted Rights Legend
　　Use, duplication, or disclosure by the Government is
　　subject to restrictions as set forth in subparagraph
　　(c) of the Commercial Computer Software - Restricted
　　Rights clause at FAR sec. 52.227-19 and subparagraph
　　(c) (1) (ii) of the Rights in Technical Data and Computer
　　Software clause at DFARS sec. 252.227-7013.
　　cisco Systems, Inc.
　　170 West Tasman Drive
　　San Jose, California 95134-1706
　　Cisco Internetwork Operating System Software

　　IOS (tm) 3600 Software (C3640-I-M), Version 12.1(2)T,>　　Copyright (c) 1986-2000 by cisco Systems, Inc.
　　Compiled Tue 16-May-00 12:26 by ccai
　　Image text-base: 0x600088F0, data-base: 0x60924000
　　cisco 3640 (R4700) processor (revision 0x00) with 24576K/8192K bytes of memory.

　　Processor board>　　R4700 CPU at 100Mhz, Implementation 33, Rev 1.0
　　Bridging software.
　　X.25 software, Version 3.0.0.
　　2 FastEthernet/IEEE 802.3 interface(s)
　　1 Serial network interface(s)
　　DRAM configuration is 64 bits wide with parity disabled.
　　125K bytes of non-volatile configuration memory.
　　8192K bytes of processor board System flash (Read/Write)
　　--- System Configuration Dialog ---
　　Would you like to enter the initial configuration dialog? [yes/no]: y
　　您是否进入初始化配置对话,选Y
　　At any point you may enter a question mark '?' for help.
　　Use ctrl-c to abort configuration dialog at any prompt.
　　Default settings are in square brackets '[]'.Basic management setup configures only enough connectivity
　　for management of the system, extended setup will ask you
　　to configure each interface on the system
　　Would you like to enter basic management setup? [yes/no]: n
　　您是否进入基本配置安装,选N
　　First, would you like to see the current interface summary? [yes]: y
　　首先,您是否看一下当前端口状态
　　Any interface listed with OK? value "NO" does not have a valid configuration
　　Interface IP-Address OK? Method Status Protocol
　　FastEthernet0/0unassigned NO unset up down
　　Serial0/0 unassigned NO unset down down
　　FastEthernet0/1unassigned NO unset up down
　　Configuring global parameters:
　　Enter host name [Router]:RouterA
　　输入路由器的名字
　　The enable secret is a password used to protect access to
　　privileged EXEC and configuration modes. This password, after
　　entered, becomes encrypted in the configuration.
　　Enter enable secret: aaa
　　输入密文
　　The enable password is used when you do not specify an
　　enable secret password, with some older software versions, and
　　some boot images.
　　Enter enable password: bbb
　　输入密码(不能和密文相同)
　　The virtual terminal password is used to protect
　　access to the router over a network interface.
　　Enter virtual terminal password: ccc
　　输入虚拟终端的密码(以备远程登录)
　　Configure SNMP Network Management? [yes]: n
　　配置简单网管吗?选N
　　Configure IP? [yes]: y
　　配置IP吗?选Y
　　Configure IGRP routing? [yes]: n
　　配置IGRP路由选择协议吗?选N
　　Configure RIP routing? [no]:
　　配置IGRP路由选择协议吗?选N
　　Configure bridging? [no]:
　　配置桥接吗?选N
　　Async lines accept incoming modems calls. If you will have
　　users dialing in via modems, configure these lines.
　　Configure Async lines? [yes]: n
　　配置异步线路吗?选N
　　Configuring interface parameters:
　　Do you want to configure FastEthernet0/0 interface? [yes]: y
　　您是否想配置fastethernet0/0接口?选Y
　　Use the 100 Base-TX (RJ-45) connector? [yes]: y
　　用RJ45的连接器吗?选Y
　　Operate in full-duplex mode? [no]: y
　　选用全双工模式?选Y
　　Configure IP on this interface? [yes]: y
　　在这个接口上配置IP吗?选Y
　　IP address for this interface: 192.168.0.1
　　配置该接口的IP地址(在此地址为192.168.0.1
　　Subnet mask for this interface [255.255.255.0] :
　　配置该接口的子网掩码.(默认的是255.255.255.0,可以手工输入修改)
　　Class C network is 192.168.0.0, 24 subnet bits; mask is /24
　　Do you want to configure Serial0/0 interface? [yes]: y
　　您想配置serial0/0接口吗?选Y
　　Some supported encapsulations are
　　ppp/hdlc/frame-relay/lapb/x25/atm-dxi/smds
　　Choose encapsulation type [hdlc]:
　　选择封装方式(默认的封装方式是HDLC,您可根据与您的路由器相连选用的封装类型来决定用什么样的封装类型
　　No serial cable seen.
　　Choose mode from (dce/dte) [dte]:
　　(因为没有连串口线所以会让您选择设备类型)
　　Configure IP on this interface? [yes]: y
　　(在接口上配置IP)
　　Configure IP unnumbered on this interface? [no]:
　　IP address for this interface: 172.16.0.5
　　配置该接口的IP地址(在此地址为172.16.0.5)
　　Subnet mask for this interface [255.255.0.0] : 255.255.255.252
　　配置该接口的子网掩码.(默认的是255.255.0.0,可以手工输入修改为255.255.255.252)
　　Class B network is 172.16.0.0, 30 subnet bits; mask is /30
　　(以下配置同上)
　　Do you want to configure FastEthernet0/1 interface? [yes]:
　　Use the 100 Base-TX (RJ-45) connector? [yes]:
　　Operate in full-duplex mode? [no]: y
　　Configure IP on this interface? [yes]: y
　　IP address for this interface: 172.16.0.9

　　Subnet mask for this interface [255.255.0.0] : 255.255.255.252>　　The following configuration command script was created:
　　(把您的配置显示出来)
　　hostname aaa
　　enable secret 5 $1$ul/V$ezbZFgvzGHD.YPSieC0Ew/
　　enable password RouterA
　　line vty 0 4
　　password ccc
　　no snmp-server
　　!
　　ip routing
　　no bridge 1
　　!
　　interface FastEthernet0/0
　　media-type 100BaseX
　　full-duplex
　　ip address 192.168.0.1 255.255.255.0
　　!
　　interface Serial0/0
　　encapsulation hdlc
　　ip address 172.16.0.5 255.255.255.252
　　!
　　interface FastEthernet0/1
　　media-type 100BaseX
　　full-duplex
　　ip address 172.16.0.9 255.255.255.252
　　dialer-list 1 protocol ip permit
　　dialer-list 1 protocol ipx permit
　　!
　　end
　　以下提示您是否保存这次设置
　　[0] Go to the IOS command prompt without saving this config.
　　[1] Return back to the setup without saving this config.
　　[2] Save this configuration to nvram and exit.
　　Enter your selection [2]: 2
　　选择2保存设置并存入NVRAM中
　　Building configuration...
　　[OK] Use the enabled mode 'configure' command to modify this configuration.
　　Press RETURN to get started!
　　路由器重新启动
　　00:00:08: %LINK-3-UPDOWN: Interface Serial0/0, changed state to down
　　00:00:08: %LINK-3-UPDOWN: Interface FastEthernet0/0, changed state to up
　　00:00:08: %LINK-3-UPDOWN: Interface FastEthernet0/1, changed state to up
　　00:00:09: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/0, changed state to down
　　00:00:09: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to down
　　00:00:09: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/1, changed state to down
　　00:03:18: %IP-5-WEBINST_KILL: Terminating DNS process
　　00:03:24: %SYS-5-RESTART: System restarted --
　　Cisco Internetwork Operating System Software

　　IOS (tm) 3600 Software (C3640-I-M), Version 12.1(2)T,>　　Copyright (c) 1986-2000 by cisco Systems, Inc.
　　Compiled Tue 16-May-00 12:26 by ccai
　　RouterA>
　　进入用户模式
　　RouterA>en
　　Password:
　　RouterA#
　　进入全局模式
　　RouterA#sh run
　　查看现在运行的配置
　　Building configuration...
　　Current configuration:
　　!
　　version 12.1
　　service timestamps debug uptime
　　service timestamps log uptime
　　no service password-encryption
　　!
　　hostname RouterA
　　!
　　enable secret 5 $1$ul/V$ezbZFgvzGHD.YPSieC0Ew/
　　enable password bbb
　　!
　　memory-size iomem 25
　　ip subnet-zero
　　!
　　interface FastEthernet0/0
　　ip address 192.168.0.1 255.255.255.0
　　speed auto
　　full-duplex
　　!
　　interface Serial0/0
　　ip address 172.16.0.5 255.255.255.252
　　clockrate 2000000
　　!
　　interface FastEthernet0/1
　　ip address 172.16.0.9 255.255.255.252
　　speed auto
　　full-duplex
　　!

　　ip>　　no ip http server
　　!
　　dialer-list 1 protocol ip permit
　　dialer-list 1 protocol ipx permit
　　!
　　line con 0
　　transport input none
　　line aux 0
　　line vty 0 4
　　password ccc
　　login
　　!
　　end