LNMP环境下php-fpm启动脚本

tseew

安装LNMP环境，PHP5.4.37版本安装成功，添加php-fpm服务到系统启动项时，报错service php-fpm does not support chkconfig；php-fpm服务不支持chkconfig；
编辑/etc/init.d/php-fpm启动脚本，打开之后是乱码，查找原因是拷贝php-fpm启动脚本文件错误。
从同样环境下同样的php版本拷贝php-fpm启动脚本，重新编辑黏贴过来，保存退出后，可以正常加入启动项；有遇到同样情况的朋友可以直接复制脚本，保持与脚本内容的路径一样即可。


php-fpm启动脚本参考如下：

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114

#! /bin/sh ### BEGIN INIT INFO # Provides:          php-fpm # Required-Start:    $remote_fs $network # Required-Stop:     $remote_fs $network # Default-Start:     2 3 4 5 # Default-Stop:      0 1 6 # Short-Description: starts php-fpm # Description:       starts the PHP FastCGI Process Manager daemon ### END INIT INFO prefix=/usr/local/php exec_prefix=${prefix} php_fpm_BIN=${exec_prefix}/sbin/php-fpm php_fpm_CONF=${prefix}/etc/php-fpm.conf php_fpm_PID=${prefix}/var/run/php-fpm.pid php_opts="--fpm-config $php_fpm_CONF --pid $php_fpm_PID" wait_for_pid () { try=0 while test $try -lt 35 ; do   case "$1" in    'created')    if [ -f "$2" ] ; then     try=''     break    fi    ;;    'removed')    if [ ! -f "$2" ] ; then     try=''     break    fi    ;;   esac   echo -n .   try=`expr $try + 1`   sleep 1 done } case "$1" in start)   echo -n "Starting php-fpm "   $php_fpm_BIN --daemonize $php_opts   if [ "$?" != 0 ] ; then    echo " failed"    exit 1   fi   wait_for_pid created $php_fpm_PID   if [ -n "$try" ] ; then    echo " failed"    exit 1   else    echo " done"   fi ;; stop)   echo -n "Gracefully shutting down php-fpm "   if [ ! -r $php_fpm_PID ] ; then    echo "warning, no pid file found - php-fpm is not running ?"    exit 1   fi   kill -QUIT `cat $php_fpm_PID`   wait_for_pid removed $php_fpm_PID   if [ -n "$try" ] ; then    echo " failed. Use force-quit"    exit 1   else    echo " done"   fi ;; status)   if [ ! -r $php_fpm_PID ] ; then    echo "php-fpm is stopped"    exit 0   fi   PID=`cat $php_fpm_PID`   if ps -p $PID | grep -q $PID; then    echo "php-fpm (pid $PID) is running..."   else    echo "php-fpm dead but pid file exists"   fi ;; force-quit)   echo -n "Terminating php-fpm "   if [ ! -r $php_fpm_PID ] ; then    echo "warning, no pid file found - php-fpm is not running ?"    exit 1   fi   kill -TERM `cat $php_fpm_PID`   wait_for_pid removed $php_fpm_PID   if [ -n "$try" ] ; then    echo " failed"    exit 1   else    echo " done"   fi ;; restart)   $0 stop   $0 start ;; reload)   echo -n "Reload service php-fpm "   if [ ! -r $php_fpm_PID ] ; then    echo "warning, no pid file found - php-fpm is not running ?"    exit 1   fi   kill -USR2 `cat $php_fpm_PID`   echo " done" ;; *)   echo "Usage: $0 {start|stop|force-quit|restart|reload|status}"   exit 1 ;; esac