Interrupt within 5 seconds to abort boot process.
Boot process failed...
The system is unable to boot automatically. The BOOT
environment variable needs to be set to a bootable
image.
switch:
switch:
============================================================================
这个完蛋了,交换机里flash文件丢失了,不知道是什么原因造成的。先不管什么原因,打电脑给思科技术,哎,都打不通,思科服务,真无话可说了,又联系一家思科代理公司,上门维修报价2000元,太贵了。上网查一下有没有其他办法解决,终于找到一个完美解决方法,步骤如下:
一.上网下载一个同型号的bin文件c3560-advipservicesk9-mz.122-25.SEE2.bin
第一种方法:X-Modem
1、用控制线连接交换机console口与计算机串口1,用带有xmodem功能的终端软件连接(win2000 and xp的超级终端就带这功能)。
2、设置连接方式为串口1(如果连接的是其他串口就选择其他串口),速率9600,无校验,无流控,停止位1。或者点击默认设置也可以。
3、连接以后计算机回车出现交换机无ios的界面,一般的提示符是:switch:
4、拔掉交换机后的电源线重新启动交换机
5、在超级终端输入:
switch:flash_init
会出现如下提示:
Initializing Flash...
6:输入拷贝指令:
switch:copy xmodem: flash:c3560-advipservicesk9-mz.122-25.SEE2.bin
出现如下提示:
Begin the Xmodem or Xmodem-1K transfer now...
7、系统提示不断出现C这个字母就可以开始传文件了
8、点击超级终端菜单:传送---发送文件,在协议选项中选择Xmodem或者Xmodem-1K协议,然后选择ios的影像文件(flash:c3560-advipservicesk9-mz.122-25.SEE2.bin),开始传送。
9、因为不能改速率,所以传送得很慢,我的大概传送了80分钟左右,请耐心等待。
10、传送完毕后提示:
File "xmodem:" successfully copied to ....
switch:
11、在提示符下输入
switch:boot
启用新的ios系统
12、重新加电完成恢复工作。 终于可爱的启动@@@@@@@@@@@界面就出现了,内心特别高兴,为公司省了这么多钱,同时自己也学到了这个方法,最后把相关配置配上所有员工就可以上网了。
但上网查到有最好的方法,这里跟大家共享一下: 这个是我恢复的方法,现在看来非常的不科学,效率低。后来看了别人同样用X-Modem恢复IOS,但是效率要高的方法:
先打开超级终端,进入rommon 模式(Ctrl+Break组合键),键入confreg, 如下:
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
rommon 1 > confreg 回车
Configuration Summary
enabled are:
load rom after netboot fails
console baud: 9600
boot: image specified by the boot system commands
or default to: cisco2-C2600
do you wish to change the configuration? y/n [n]: y (选择 yes)
enable "diagnostic mode"? y/n [n]: n (选择 no)
enable "use net in IP bcast address"? y/n [n]: n (选择 no)
disable "load rom after netboot fails"? y/n [n]: n (选择 no)
enable "use all zero broadcast"? y/n [n]: n (选择 no)
enable "break/abort has effect"? y/n [n]: n (选择 no)
enable "ignore system config info"? y/n [n]: n (选择 no)
change console baud rate? y/n [n]: y (选择 yes)
enter rate: 0 = 9600, 1 = 4800, 2 = 1200, 3 = 2400
4 = 19200, 5 = 38400, 6 = 57600, 7 = 115200 [0]: 7 (选择 7,用最大的115200速率的xmodem传输)
change the boot characteristics? y/n [n]: n (选择 no)
Configuration Summary
enabled are:
load rom after netboot fails
console baud: 115200
boot: image specified by the boot system commands
or default to: cisco2-C2600
do you wish to change the configuration? y/n [n]: n (选择 no)
You must reset or power cycle for new config to take effect
rommon 2 > reset 回车
注意:在此时键入 reset键之前,开始定义串口速度(我的电脑---端口属性----串口速度调为115200),然后再修改超级终端里设置速率为115200,记住,一定这么做!否则出现乱码! 然后关闭这个超级终端,重新建立一个超级终端连接,(期间系统重新启动)启动后,出现
rommon 1> 提示符
然后,输入
rommon 1> xmodem -r
Do not start the sending program yet...
Invoke this application only for disaster recovery.
Do you wish to continue? y/n [n]: y (选择 yes)
Ready to receive file ...
(videre注:实际用的时候,我发现这个命令总是改不成功,后来发现在line con 0下面有了一个speed 115200,所以即使改register成功,启动以后router又执行speed 115200,还是不行,所以如果有这个问题,记得把这个语句no掉)
Router>en 进入新IOS的特权模式
Router#reload 重启系统
Proceed with reload? [confirm] 回车
00:01:04: %SYS-5-RELOAD: Reload requested
System Bootstrap, Version 11.3(2)XA4, RELEASE SOFTWARE (fc1)
Copyright (c) 1999 by cisco Systems, Inc.
TAC:Home:SW:IOS:Specials for info
PC = 0xfff0a530, Vector = 0x500, SP = 0x680127b0
C2600 platform with 24576 Kbytes of main memory
PC = 0xfff0a530, Vector = 0x500, SP = 0x80004684
monitor: command "boot" aborted due to user interrupt
rommon 1 > confreg ( 输入“confreg”命令)
Configuration Summary
enabled are:
load rom after netboot fails
console baud: 115200
boot: image specified by the boot system commands
or default to: cisco2-C2600
do you wish to change the configuration? y/n [n]: y (选择 yes)
enable "diagnostic mode"? y/n [n]: n (选择 no)
enable "use net in IP bcast address"? y/n [n]: n (选择 no)
disable "load rom after netboot fails"? y/n [n]: n (选择 no)
enable "use all zero broadcast"? y/n [n]: n (选择 no)
enable "break/abort has effect"? y/n [n]: n (选择 no)
enable "ignore system config info"? y/n [n]: n (选择 no)
change console baud rate? y/n [n]: y (选择 yes)
enter rate: 0 = 9600, 1 = 4800, 2 = 1200, 3 = 2400
4 = 19200, 5 = 38400, 6 = 57600, 7 = 115200 [7]: 0 (选择 0,改回用标准速率速率9600的xmodem传输)
change the boot characteristics? y/n [n]: n (选择 no)
Configuration Summary
enabled are:
load rom after netboot fails
console baud: 9600
boot: image specified by the boot system commands
or default to: cisco2-C2600
do you wish to change the configuration? y/n [n]: n
You must reset or power cycle for new config to take effect
rommon 2 >
此时手工改回计算机串口与超级终端2者传输速率为9600
然后敲入
rommon 2 >reset
( 最好关电源)
他的方法有两个地方和我的不一样,首先是他在启动后进入了rommon模式,其次是他修改了串口的速率,这样就比我快的多了。