Vmware中克隆虚拟机后的克隆机网卡无法启动的解决方法

hdfdtr

  好了今天给大家分享下，由于在日常使用中，安装Linu新系统太费时间，因此克隆系统就成了大家的首选，然而这并不是一切顺利的，你会发现克隆后，克隆机网卡无法启动的现象。OK,开始解决方法吧！

1、首先，进入以下目录：

[iyunv@localhost ~]# cd /etc/udev/rules.d/

2、修改配置文件如下：

原来的：[iyunv@localhost rules.d]# vim 70-persistent-net.rules
# This file was automatically generated by the /lib/udev/write_net_rules
# program, run by the persistent-net-generator.rules rules file.
#
# You can modify it, as long as you keep each rule on a single
# line, and change only the value of the NAME= key.

# PCI device 0x8086:0x100f (e1000)
SUBSYSTEM=="net", ACTION=="add", DRIVERS=="?*", ATTR{address}=="00:0c:29:11:05:1e", ATTR{type}=="1", KERNEL=="eth*", NAME=
"eth0"

# PCI device 0x8086:0x100f (e1000)
SUBSYSTEM=="net", ACTION=="add", DRIVERS=="?*", ATTR{address}=="00:0c:29:aa:8b:bf", ATTR{type}=="1", KERNEL=="eth*", NAME=
"eth1"
修改后的：[iyunv@localhost rules.d]# vim 70-persistent-net.rules
# This file was automatically generated by the /lib/udev/write_net_rules
# program, run by the persistent-net-generator.rules rules file.
#
# You can modify it, as long as you keep each rule on a single
# line, and change only the value of the NAME= key.

# PCI device 0x8086:0x100f (e1000)
#SUBSYSTEM=="net", ACTION=="add", DRIVERS=="?*", ATTR{address}=="00:0c:29:11:05:1e", ATTR{type}=="1", KERNEL=="eth*", NAME
="eth0"

# PCI device 0x8086:0x100f (e1000)
SUBSYSTEM=="net", ACTION=="add", DRIVERS=="?*", ATTR{address}=="00:0c:29:aa:8b:bf", ATTR{type}=="1", KERNEL=="eth*", NAME=
"eth0"

3、修改网卡参数：
[iyunv@localhost ~]# vim /etc/sysconfig/network-scripts/ifcfg-eth0
DEVICE=eth0
HWADDR=00:0c:29:aa:8b:bf         *修改为上边的红色的MAC地址*
TYPE=Ethernet
UUID=d7849a85-3812-4026-ab92-b2fa58b28ecf
ONBOOT=yes
NM_CONTROLLED=yes
BOOTPROTO=none
IPADDR=192.168.255.252           *配置新的IP地址*
NETMASK=255.255.255.0
DNS2=4.4.4.4
DNS1=8.8.8.8
IPV6INIT=no
USERCTL=no

4、重启系统，查看网卡是否正常启动，ip地址是否正常。
[iyunv@localhost ~]# shutdown -r now                       *重启系统*
[iyunv@localhost ~]# ifconfig
eth0      Link encap:Ethernet  HWaddr 00:0C:29:AA:8B:BF  
          inet addr:192.168.255.252  Bcast:192.168.255.255  Mask:255.255.255.0
          inet6 addr: fe80::20c:29ff:feaa:8bbf/64 Scope:Link
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:900 errors:0 dropped:0 overruns:0 frame:0
          TX packets:788 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:87807 (85.7 KiB)  TX bytes:115265 (112.5 KiB)

lo        Link encap:Local Loopback  
          inet addr:127.0.0.1  Mask:255.0.0.0
          inet6 addr: ::1/128 Scope:Host
          UP LOOPBACK RUNNING  MTU:65536  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0
          RX bytes:0 (0.0 b)  TX bytes:0 (0.0 b)


可见，网卡启动正常，ip地址ok。